hiltfit.blogg.se - Trex miner webui

#TREX MINER WEBUI DRIVER#
#TREX MINER WEBUI FULL#
#TREX MINER WEBUI PASSWORD#

The output from step 2 is your API key, and it needs to be added as an extra T-Rex parameter in your *.bat/ *.sh.

(Windows) If a new command prompt opens and quickly closes, go to step 1 and run the command prompt under Administrator.

#TREX MINER WEBUI PASSWORD#

The password must be 8-64 characters long, without spaces, and mustĬontain at least one digit, lowercase, and uppercase letters. Open command prompt and navigate to the directory where the miner executable is.In order to be able to modify/update the settings, you need to set up a password as a security measure to prevent others Securityīy default, T-Rex WebUI provides read-only access to your mining statistics information and rig configuration. Alternatively, to bind to ALL available network interfaces, use -api-bind-http 0.0.0.0:4067 - the URL to access the monitoring page will appear in the miner console. If you would like to use it from other machines in your local network you need to set -api-bind-http parameter, e.g.

Try reducing memory overclock of the GPU that frequently trips LHR.T-Rex comes with a built-in web monitoring/control page.īy default, it is only accessible from the same PC where the miner is running.Do not delay applying overclock - this will mess up calibration results and the miner will display unrealistically high LHR tune values.Avoid using RDP if it puts load on your LHR cards. Make sure you don't have monitors connected to your LHR cards, or at least turn them off during miner start up to let it calibrate correctly.

Windows - 512.xx (although 472.xx works fine too)Ī few tips if you experience frequent LHR locks: The miner will calibrate the unlocker and the hashrate should go up to its normal level in about a minute after the miner displays calibration finished message.

Make sure you remove any -lhr-tune settings you may have in your existing configuration.

(Linux) Memory temperature is not displayed on some GDDR6X cards.

Change default value of -lhr-autotune-mode parameter to down (used to be full).

( ethash) Improve LHR unlock functionality (dual modes and autolykos2 LHR performance is unchanged)Įxpect about 78-79% in normal mode, and 75% in low power mode (see -lhr-low-power).

It will not work properly with older drivers.

#TREX MINER WEBUI DRIVER#

IMPORTANT: LHR unlocker requires 512.xx version of the driver on Windows, and 510.xx on Linux.

( ethash, blake3) "Duplicate share" issue.

LHR unlocker is more stable compared to 0.25.12, infinite LHR lock loops should be solved now.

If you previously had -lhr-low-power in your config, the equivalent would be -lhr-low-power 1 (or "lhr-low-power": "1" in HiveOS). lhr-low-power 0,1,1,0 - the second and third GPUs will be working in low power mode.

(LHR) Low power mode can now be set for GPUs individually, e.g.

(LHR) Change -lhr-autotune-step-size default value to 0.1 (previously 0.5).

#TREX MINER WEBUI FULL#

lhr-autotune-interval 5:120, meaning that in -lhr-autotune-mode full mode the miner will be increasing LHR tune value every 5 minutes, and decreasing it as soon as it starts tripping LHR more frequently than once every two hours. (LHR) Allow setting "up" and "down" auto-tune intervals separately, e.g.LHR tune values aren't accurate, but once you've found a value that's stable for your GPU, you can set it manually with -lhr-tune and get consistent results across miner restarts. (LHR) Extend the new LHR unlock functionality to ETH+ALPH dual mining, and ERGO single mode.